All units comply with the latest edition of AHRI Standard 440 for testing and rating fan coil units, are certified, and display the AHRI symbol. Sizes 14 through 20 exceed the maximum airflow rate in AHRI 440 and are outside of the scope of certification. 


​High efficiency motors, fan relays, disconnects and fusing mean easier coordination between mechanical and electrical trades. All HP Series fan coil units have a side access electrical enclosure, allowing easy access to all electrical components, terminal blocks and wiring. Available factory installed control packages can greatly reduce field labor and setup time. Consisting of control transformer and all needed relays, these packages integrate seamlessly with either factory provided thermostats or field installed thermostats and controllers.


STANDARD FEATURES
Construction
All Units

  • AHRI 440 certified and labeled
  • Galvanized steel construction
  • 1/2” thick fiberglass insulation
  • 1 1/2” duct discharge collar
  • Holes are provided at four points for hanging units

Plenum Units

  • Integral filter rack with 1” throwaway filter
  • Integral rear ducted return - field reversible to bottom return

Exposed Units

  • Single deflection rear return grille
  • Double deflection discharge grille
  • Durable powder coat paint
  • 18 gauge cabinet construction

Coils

  • AHRI 410 certified and labeled
  • Cooling - 3, 4 or 6 row chilled water or DX, heat pump compatible
  • Heating - 1, 2, 3 or 4 row hot water or 1 or 2 row steam - reheat or preheat position
  • 8 total rows of cooling and heating coils maximum
  • 3/8” O.D. seamless copper tubes
  • 0.012” tube wall thickness
  • High efficiency aluminum fin surface for optimizing heat transfer, pressure drop and carryover
  • Left or right hand connections – field reversible (water coils only)
  • Removable for service
  • Manual air vent

Drain Pans

  • Single wall, galvanized steel, externally insulated – fire retardant and antimicrobial closed cell foam
  • Double sloped to drain connection
  • Removable, field reversible
  • 7/8” O.D. primary drain connection

Fan Assemblies

  • Forward curved, DWDI centrifugal type
  • 115 volt, single phase, three tap PSC motors
  • Quick disconnect motor connections
  • Removable fan(s)/motor(s) for service

Electrical

  • cETL listed for safety compliance
  • Electrical junction box for field wiring terminations
  • Terminal block for field connections

Electric Heat

  • cETL listed as an assembly for safety compliance
  • Integral electric heat assembly with removable elements for easy service
  • Automatic reset primary and back-up secondary thermal limits
  • Single point power connection
  • Side-hinged electrical enclosure


OPTIONAL FEATURES
Construction
All Units

  •  Foil faced fiberglass insulation
  •  Elastomeric closed cell foam insulation

Plenum Units

  • Bottom return
  • Mixing box with top/rear or rear/bottom dampers - field reversible
  • Damper actuator
  • Spare 1” throwaway filters
  • 1” and 2” pleated filters

Exposed Units

  • Single deflection bottom return grille
  • Ducted supply
  • Ducted rear return

Coils

  • 1/2” O.D. seamless copper tubes
  • 0.016” tube wall thickness
  • 0.025” tube wall thickness
  • Automatic air vents
  • Stainless steel coil casings

Drain Pans

  • Stainless steel with external insulation
  • 5/8” O.D. secondary drain connection
  • Auxiliary drip pans

Fan Assemblies

  • 208-230 & 277 volt, single phase, three tap PSC motors
  • ECM™ motors

Electrical

  • Side access electrical enclosure
  • Silent solid state fan relays
  • SCR fan speed controller (only for high speed)
  • Toggle disconnect switch
  • Condensate overflow switch (drain pan)
  • Main fusing
  • Unit and remote mounted three speed fan switches
  • Fan relay packages
  • Control power transformers

Electric Heat

  • Door interlocking disconnect switches
  • Main fusing
  • Silent relay / contactor

Thermostats

  • Remote mounted analog, digital display or programmable
  • 2 and 4 pipe control sequences
  • Automatic and manual changeover
  • Integral three speed fan switches


COILS
ENVIRO-TEC offers hot water, chilled water, direct expansion (DX), and standard steam coils for specific application with all HP Series Fan Coil Units. Strict on-site inspection before, during, and after installation guarantees the highest quality and performance available.

STANDARD FEATURES

  • Cooling - 3, 4 or 6 row chilled water or DX
  • Heating - 1, 2, 3 or 4 row hot water, or 1 or 2 row steam
  • 8 total rows of cooling and heating coils maximum
  • 3/8” O.D. seamless copper tubes
  • 0.012” tube wall thickness
  • High efficiency aluminum fin surface for optimizing heattransfer, pressure drop and carryover
  • Left or right hand connections
  • Manual air vents


OPTIONAL FEATURES

  • 1/2” O.D. seamless copper tubes
  • 0.016” tube wall thickness
  • 0.025” tube wall thickness
  • Automatic air vents
  • Stainless steel coil casings
  • DX coils are heat pump compatible

Lewis Mechanical Sales logo
Enviro Tec logo

Enviro-Tec 


Horizontal Low Profile HP


The ENVIRO-TEC HP Series horizontal high performance fan coil units are designed to maximize flexibility of selection and installation. The units are also designed to exceed the stringent quality standards of the institutional market, while remaining cost competitive in the light commercial segment of the market.

Enviro-Tec Horizontal Low Profile HP FCU

(High Performance)



The ENVIRO-TEC HP Series horizontal high performance fan coil units are designed to maximize flexibility of selection and installation.

Enviro Tec Horizontal Low Profile HP FCU
Enviro Tec logo

          Steve Lewis LLC dba

Peace of Mind
33 Years of Combined Experience
361-882-2233

Call Us Today for Your Next Project

Locally Owned & Operated